All brands from all over the world

All brands from all over the world read more »
Close window

All brands from all over the world

Close filters
 
  •  
  •  
  •  
  •  
  •  
  •  
  •  
from to
 
16 From 65
No results were found for the filter!
NEW
EEPROM 4 click
EEPROM 4 click
EEPROM 4 click is 2,097,152 bits on a click board™, organized into 262,144 bytes. In other words, this click board™ is an EEPROM memory medium with the capacity of 256 KB . The used EEPROM module has very good endurance and it can...
$1,579.00 *
NEW
Flash 4 click
Flash 4 click
The S25FL512S module can withstand up to 100,000 program cycles, with the data retention period of minimum 20 years. The flash memory IC used on this Click board™ features Serial Flash Discoverable Parameters (SFDP) mode, used to...
$2,629.00 *
NEW
Signal Relay click
Signal Relay click
Signal Relay click can be used for ON/OFF control in various devices. It carries four ultra-small GV5-1 PCB relays from Omron and runs on a 5V power supply. Signal Relay click communicates with the target MCU over the following mikroBUS...
$3,049.00 *
NEW
FLICKER click
FLICKER click
FLICKER click Thanks to the onboard NA556 dual precision timer from Texas Instruments and the G6D-ASI power PCB relay from Omron, the FLICKER click can control loads up to 5A, 250 VAC/30 VDC at a predefined time interval. The on/off...
$1,999.00 *
NEW
Relay2 click
Relay2 click
Description Relay 2 click carries two LCA717 single-pole, OptoMOS® solid state relays and two screw terminals for connecting the wiring. These relays have a load current of 2A, low maximum on-resistance of just 0.15 Ohms, and a blocking...
$2,729.00 *
NEW
UNIQUE ID click
UNIQUE ID click
Description Unique ID click carries DS2401 , an enhanced silicon serial number IC. It’s a low cost solution for providing a unique registration number to your design. The chip consists of a factory-lasered 64-bit ROM that includes a...
$949.00 *
NEW
PROTO click
PROTO click
PROTO click is an accessory board in mikroBUS form factor. It features 10x11 prototyping area as well as additional power pads. It can be used to assemble custom electronics thus creating a custom click board. The board provides 3.3V and...
$469.00 *
NEW
RELAY click
RELAY click
RELAY click can control various devices with up to 5A, 250V AC/30V DC loads. It features two G6D1AASI-5DC power PCB relay modules. The click is designed to run on 5V power supply only. RELAY click communicates with the target...
$1,889.00 *
NEW
OPTO click
OPTO click
OPTO Click is an accessory board in mikroBUS form factor. It features two VO2630 dual channel, high speed optocoupler modules. They enable high speed (10 MBit/s) data transfer between it’s input and output with galvanic isolation ....
$2,209.00 *
NEW
Opto 2 click
Opto 2 click
Opto 2 click is an optical isolator used to provide an optical galvanic isolation of sensitive lines. The used optoisolation elements require very low input current to be driven, down to 1.3mA (min). The speed of the internal optocoupler...
$2,629.00 *
NEW
Tester click
Tester click
Each pin of the mikroBUS™ is routed to a red colored LED, which is protected by 1K resistor. This allows voltages up to VCC to be handled with no issues, providing a simple and clean solution for pin state testing. Once placed on the...
$629.00 *
NEW
Relay 3 Click
Relay 3 Click
Besides two relays, the Click board™ contains all the necessary electronic components for driving the relay coils. Two LED indicators provide visual feedback about the activity of the relays. Although it can withstand up to 7A through...
$1,889.00 *
16 From 65
Viewed