No results were found for the filter!
LPCXpresso Click Shield
LPCXpresso is the development platform pioneered by NXP® and Embedded Artists. It includes low-cost LPCXpresso target boards which are designed for simple, rapid prototyping and evaluation. LPCXpresso development boards work with the MCU...
Feather Click Shield
The Feather is Adafruit’s standardized open source development platform for IoT projects. The Adafruit Feather & FeatherWing system consist of base board (Feather) and expansion boards (Wings). They are connected to each other over...
mikroBUS Shuttle is a small add-on board, which is intended to be used with Shuttle click , in order to expand the mikroBUS™ with additional stacking options. This small add-on board has one mikroBUS™ equipped on itself and it is...
MCP2542 is designed specifically for high-speed CAN FD applications with communication speeds of up to 8 Mbps. Longer than usual BUS lengths are supported thanks to the improved maximum propagation delay. The board has a standard RS232...
RS485 Isolator click
RS485 Isolator click is a RS485 communication isolator, and carries the ADM2682EBRIZ , a 5 kV rms signal and power isolated RS-485 transceiver. The click is designed to run on either 3.3V or 5V power supply. It communicates with the...
CAN Isolator click
CAN Isolator click provides isolated CAN communication. It carries the ADM3053 signal and power isolated CAN transceiver with an integrated isolated DC-to-DC converter. The click is designed to run on either 3.3V or 5V power supply. CAN...
ATA6563 click carries the ATA6563 high-speed CAN transceiver. The click is designed to run on a 5V power supply. Use the VIO SEL jumper for selecting the 3.3V or 5V logic level. It communicates with the target microcontroller over UART...
RS485 2 click
RS485 2 click carries the MAX3471 half-duplex transceiver intended for lithium battery-powered RS-485/RS-422 applications. The click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller...
I2C Isolator 2 click
I2C Isolator 2 click provides I2C lines and power isolation for slave devices. It carries the ADM3260 dual I2C isolator with an integrated DC-to-DC converter. I2C Isolator 2 click is designed to run on either 3.3V or 5V power supply. The...
USB UART 2 Click
USB UART 2 click provides USB isolation and carries the ADUM4160BRWZ USB port isolator. The click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller over UART interface, with additional...
SPI Isolator click
SPI Isolator click carries the ADuM4154 5kV digital isolator optimized for a serial peripheral interface (SPI). The click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller over SPI...
The click communicates with the target MCU through the UART interface and runs on a 3.3V power supply. ATA663211 click can aslo be used as a standalone LIN transceiver, without being connected to a mikroBUS™ socket. An onboard LDO...
I2C Isolator ETH Click SPI Isolator RS485 click 5V Intel Joule Pi click shield I2C 1-Wire RS485 3 click FTDI click 1-Wire I2C iButton click Feather Click PICtail Plus MCP2542 click ATA663211 click ATA6563 click PWM 2 click USB SPI click Arduino UNO DALI 2 click RS232 2 click Expand 3 click UART I2C SPI mikroBUS 4-20 mA R click Intel Joule Expand 2 click Expand 4 click FRDM KL46 click click BOOSTER Arduino MEGA UART 1-Wire CAN SPI click USB I2C click I2C Isolator 2 BroadR-Reach STM32F4 RS485 2 click mikroBus Cape MCP2517FD click RS232 click MCP25625 click PI2 click OBDII click RS485 click RS485 Isolator