1-Wire I2C click

Please inform me as soon as the product is available again.
₹2,309.00 *

Prices incl. VAT plus shipping costs

Out of Stock

  • MIKROE-2750
  • MIKROE-2750
1-Wire I2C click  carries DS28E17 1-Wire-to-I2C master bridge from Maxim Integrated. The... more
Product information "1-Wire I2C click"

1-Wire I2C click carries DS28E17 1-Wire-to-I2C master bridge from Maxim Integrated. The click runs on a 3.3V power supply.

It communicates with the target microcontroller over 1-Wire® protocol, using the following pins on the mikroBUS™ line: AN, PWM, RST.

How the click works

There are two on-board screw terminals used for connecting SCL, SDA, Vcc and GND of the I2C slave. After that, you are able to communicate with that slave through the onboard DS28E17 MCU.

DS28E17 features

The DS28E17 is a 1-Wire slave to I2C master bridge device that interfaces directly to I2C slaves at standard (100kHz max) or fast (400kHz max). Data transfers serially through the 1-Wire® protocol, which requires only a single data lead and a ground return. Every DS28E17 is guaranteed to have a unique 64-bit ROM registration number that serves as a node address in the 1-Wire network.

Specifications

Type 1-wire
Applications 1-Wire I2C click can be used to extend the length of I2C lines by converting I2C to 1-wire
On-board modules DS28E17 1-Wire-to-I2C master bridge from Maxim Integrated
Interface 1-wire,GPIO
Input Voltage 3.3V
Click board size S (28.6 x 25.4 mm)

Pinout diagram

This table shows how the pinout on 1-Wire I2C click corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).

Notes Pin Mikrobus logo.png Pin Notes
1-Wire 1st pin OW1 1 AN PWM 16 OW2 1-Wire 2nd pin
Reset pin RST 2 RST INT 15 NC  
  NC 3 CS TX 14 NC  
  NC 4 SCK RX 13 NC  
  NC 5 MISO SCL 12 NC  
  NC 6 MOSI SDA 11 NC  
Power supply +3.3V 7 3.3V 5V 10 NC  
Ground GND 8 GND GND 9 GND Ground

Programming

Code examples for 1-Wire I2C click, written for MikroElektronika hardware and compilers are available on Libstock.

Code snippet

The following code snippet shows 1-Wire I2C click communication with the Thermo 4 click. It uses skipRom, writeI2C, and readI2C commands to read the temperature data from the sensor, and displays it back via UART output.

01 void One_Wire_I2C_Task()
02 {
03     char uartText [20];
04     char IWireData [20];
05
06    IWireData [0] = 0x00;   //Thermo 4 temperature register address
07
08    OWI2C_skipRom ();
09     OWI2C_writeI2C ( OWI2C_WRITE_NORMAL_NOSTOP, 0x48, 1, &IWireData);   //0x48 is unshifted I2C address of Thermo 4 click
10     OWI2C_skipRom ();
11     OWI2C_readI2C ( 0x48, 2, &IWireData);
12
13    UART_Write (13);
14     UART_Write (10);
15     UART_Write_Text("Current temperature is: ");
16     ByteToStr(IWireData[0], uartText);
17     UART_Write_Text(uartText);
18
19    Delay_ms (2000);
20 }

Downloads

 mikroBUS™ Standard specification 
 1-Wire I2C click schematic
 DS28E17 datasheet

 LibStock: 1-Wire I2C click librar

Related links to "1-Wire I2C click"
Read, write and discuss reviews... more
Customer evaluation for "1-Wire I2C click"
Write an evaluation
Evaluations will be activated after verification.
Please enter these characters in the following text field.

The fields marked with * are required.

Viewed