WiFi2 click

Please inform me as soon as the product is available again.
₹3,049.00 *

Prices incl. VAT plus shipping costs

Out of Stock

  • MIKROE-1768
  • MIKROE-1768
WiFi2 click  features the  HLK-M30  WiFi module with a built-in TCP/IP protocol... more
Product information "WiFi2 click"

WiFi2 click features the HLK-M30 WiFi module with a built-in TCP/IP protocol stack. The click is designed to run on a 3.3V power supply; it communicates with the target MCU over an UART interface and the following mikroBUS™ pins: AN, RST.

TCP/IP client of server

WiFi2 click can be set up both as a TCP/IP client or server. You can configure it with either a static or dynamic IP address. Use the mikroBUS™ AN line (DEF on this click) to reset WiFi2 to default factory settings if needed.

Security and network protocols

WiFi2 click supports standard security authentication systems (WEP64/WEP128/ TKIP/ AES, WEP/WPA-PSK/WPA2-PSK); as well as multiple network protocols (TCP/UDP/ DHCP/DNS). All these features make WiFi2 click ideal for home automation applications, remote controls, telemetry etc.

PBC antenna

The click features a PCB trace antenna, designed for the 2400–2483.5 MHz frequency band.

Specification

Type Wi-Fi
Applications WiFi2 click is simple to configure so is suitable for a wide range applications, including home automation, remote control and so on
On-board modules HLK-M30 WiFi
Key Features TCP/UDP/DHCP/DNS network protocols supported. Built-in EP64/WEP128/ TKIP/ AES, WEP/WPA-PSK/WPA2-PSK authentication
Key Benefits Can be configured with a static IP address
Interface GPIO,UART
Input Voltage 3.3V
Compatibility mikroBUS
Click board size M (42.9 x 25.4 mm)

Key features

  • HLK-M30 module
    • Supports 802.11b/g/n
    • TCP/UDP/DHCP/DNS network protocols supported
    • Built-in EP64/WEP128/ TKIP/ AES, WEP/WPA-PSK/WPA2-PSK authentication
  • Interface: UART
  • 3.3V power supply

Pinout diagram

This table shows how the pinout on WiFi2 click corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).

NotesPinMikrobus logo.png

mikroBUStm

PinNotes
Reset to default factory settings DEF 1 AN PWM 16 NC Not connected
Reset module RST# 2 RST INT 15 NC Not connected
Not connected NC 3 CS TX 14 TX UART transmit
Not connected NC 4 SCK RX 13 RX UART receive
Not connected NC 5 MISO SCL 12 NC Not connected
Not connected NC 6 MOSI SDA 11 NC Not connected
Power supply +3.3V 7 3.3V 5V 10 NC Not connected
Ground GND 8 GND GND 9 GND Ground

Programming

This function powers on the WiFi2 click module and must be executed before any usage of the click board functionality.

01 void WiFi2_PowerON( void )
02 {
03     WiFi2_DEF  = 1;
04     WiFi2_RST  = 0;
05     WiFi2_TX   = 0;
06     WiFi2_RX   = 0;
07     delay_ms( 500 );
08     WiFi2_RST  = 1;
09     delay_ms( 100 );
10     WiFi2_TX   = 1;
11     delay_ms( 100 );
12 }
Related links to "WiFi2 click"
Read, write and discuss reviews... more
Customer evaluation for "WiFi2 click"
Write an evaluation
Evaluations will be activated after verification.
Please enter these characters in the following text field.

The fields marked with * are required.

Viewed