Products from Mikroelektronika
No results were found for the filter!
RS485 3 click
RS485 3 click uses SN65HVD31DR from Texas Instruments , a tri-state differential line driver and differential input line receiver. The click is intended to be used as UART to RS422/RS485 communication interface. It is suited for...
USB UART 4 click
USB UART 4 click features well-known FT232RL USB-to-UART interface module from FDTI . It provides USB to asynchronous serial data transfer interface, allowing the microcontroller based designs to communicate with the personal computer,...
MCP2517FD click is a complete CAN solution which carries the MCP2517FD CAN FD controller and ATA6563 high-speed CAN transceiver from Microchip, as well as a DB9 9-pin connector. The click requires both 3.3V and 5V power supply. It...
1-Wire I2C click
1-Wire I2C click carries DS28E17 1-Wire-to-I2C master bridge from Maxim Integrated. The click runs on a 3.3V power supply. It communicates with the target microcontroller over 1-Wire® protocol, using the following pins on the mikroBUS™...
RS485 Isolator click
RS485 Isolator click is a RS485 communication isolator, and carries the ADM2682EBRIZ , a 5 kV rms signal and power isolated RS-485 transceiver. The click is designed to run on either 3.3V or 5V power supply. It communicates with the...
CAN Isolator click
CAN Isolator click provides isolated CAN communication. It carries the ADM3053 signal and power isolated CAN transceiver with an integrated isolated DC-to-DC converter. The click is designed to run on either 3.3V or 5V power supply. CAN...
ATA6563 click carries the ATA6563 high-speed CAN transceiver. The click is designed to run on a 5V power supply. Use the VIO SEL jumper for selecting the 3.3V or 5V logic level. It communicates with the target microcontroller over UART...
RS485 2 click
RS485 2 click carries the MAX3471 half-duplex transceiver intended for lithium battery-powered RS-485/RS-422 applications. The click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller...
I2C Isolator 2 click
I2C Isolator 2 click provides I2C lines and power isolation for slave devices. It carries the ADM3260 dual I2C isolator with an integrated DC-to-DC converter. I2C Isolator 2 click is designed to run on either 3.3V or 5V power supply. The...
USB UART 2 Click
USB UART 2 click provides USB isolation and carries the ADUM4160BRWZ USB port isolator. The click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller over UART interface, with additional...
SPI Isolator click
SPI Isolator click carries the ADuM4154 5kV digital isolator optimized for a serial peripheral interface (SPI). The click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller over SPI...
The click communicates with the target MCU through the UART interface and runs on a 3.3V power supply. ATA663211 click can aslo be used as a standalone LIN transceiver, without being connected to a mikroBUS™ socket. An onboard LDO...
USB SPI click Nvidia Jetson Gravity NO2 ATA6563 click Google Coral Gravity PM2.5 C2000 Delfino Google AIY CAN SPI click TRB140 - Tiva C Series Weather Station Pixhawk 4 - Luminosity Ammonia NH3 for Raspberry Pi 4 TurtleBot4 LoCoBot WX250 Sulfur Dioxide Nitric Oxide NO SparkFun USB Temperature Ultrasound Analog Alcohol Opentherm to Gravity Dust Particle Matter Capacitive RS485 2 click RaspberryPi BBC micro bit Kria KR260 Methane CH4 and Gravity Analog Ozone O3 Gas Molecular Gravity I2C Plug Sense Gravity Analog Google Coral Google AIY RS485 click 5V Weather station MCP2517FD click Ammonia NH3 Gas Gravity