Arduino MKR Fox 1200

₹4,599.00 *

Prices incl. VAT plus shipping costs

Ready to ship today,
Delivery time appr. 1-3 workdays

  • Arduino-ABX00014
Arduino MKR FOX 1200  has been designed to offer a practical and cost effective solution... more
Product information "Arduino MKR Fox 1200"

Arduino MKR FOX 1200 has been designed to offer a practical and cost effective solution for makers seeking to add SigFox connectivity to their projects with minimal previous experience in networking. It is based on the Atmel SAMD21 and a ATA8520 SigFox module.

The design includes the ability to power the board using two 1.5V AA or AAA batteries or external 5V. Switching from one source to the other is done automatically. A good 32 bit computational power similar to the Zero board, the usual rich set of I/O interfaces, low power SigFox communication and the ease of use of the Arduino Software (IDE) for code development and programming. All these features make this board the preferred choice for the emerging IoT battery-powered projects in a compact form factor. The USB port can be used to supply power (5V) to the board. The Arduino MKR FOX 1200 is able to run with or without the batteries connected and has limited power consumption.

Warning: Unlike most Arduino & Genuino boards, the MKRFOX1200 runs at 3.3V. The maximum voltage that the I/O pins can tolerate is 3.3V. Applying voltages higher than 3.3V to any I/O pin could damage the board. While output to 5V digital devices is possible, bidirectional communication with 5V devices needs proper level shifting.

You can find here your board warranty informations.

Check your area coverage on the SigFox website

Getting Started

You can find in the Getting Started section all the information you need to configure your board, use the Arduino Software (IDE), and start tinker with coding and electronics. Full details and examples on how to use the SigFox interface are available in the SigFox Library reference page.

Need Help?

Documents 

OSH: Schematics

The MKR FOX 1200 is open-source hardware! You can build your own board using the following files:

EAGLE FILES IN .ZIPSCHEMATICS IN .PDFFRITZING IN .FZPZ

Pinout

Download the pinout in PNG format

Coverage

Check your area coverage on the SigFox website

Data planning

The MKRFOX1200 price includes a subscription to the SigFox network for one year. The plan will be automatically activated after the fourth message has been sent. You can send up to 140 messages per day.

Antenna

The MKR FOX 1200 is not shipped with a GSM antenna that can be attached to the board with the micro UFL connector. If you want to change the antenna please check that it can accept frequencies in the SigFox's range (868 Mhz). GSM Antenna

Please note: for best result, do not attach the antenna to a metallic surface like car chassis, etc.

Batteries, Pins and board LEDs

Battery capacity: The connected batteries must have a nominal voltage of 1.5V 

Battery connector: If you want to connect a battery pack (2x AA or AAA) to your MKR FOX 1200 use the screw terminal block.

Polarity : as reported on the silk in the bottom of the board, positive pin is the closest to the USB connector

Vin: This pin can be used to power the board with a regulated 5V source. If the power is fed through this pin, the USB power source is disconnected. This is the only way you can supply 5v (range is 5V to maximum 6V) to the board not using USB. This pin is an INPUT.

5V: This pin outputs 5V from the the board when powered from the USB connector or from the VIN pin of the board. It is unregulated and the voltage is taken directly from the inputs. 

VCC: This pin outputs 3.3V through the on-board voltage regulator. This voltage is 3.3V if USB or VIN is used and equal to the series of the two batteries when they are used

LED ON: This LED is connected to the 5V input from either USB or VIN. It is not connected to the battery power. This means that it lits up when power is from USB or VIN, but stays off when the board is running on battery power. This maximizes the usage of the energy stored in the battery. It is therefore normal to have the board properly running on battery power without the LED ON being lit.

On board LED: On MKRFOX1200 the onboard LED is connected to D6 and not D13 as on the other boards. Blink example or other sketcthes that uses pin 13 for on board LED may need to be changed to work properly.

Related links to "Arduino MKR Fox 1200"
Read, write and discuss reviews... more
Customer evaluation for "Arduino MKR Fox 1200"
Write an evaluation
Evaluations will be activated after verification.
Please enter these characters in the following text field.

The fields marked with * are required.

I have read the data protection information.

NEW
Ozone 2 click Ozone 2 click
₹3,889.00 *
NEW
NEW
NEW
Microwave click Microwave click
₹2,629.00 *
NEW
NEW
DHT22 2 click DHT22 2 click
₹2,309.00 *
NEW
Thermo J click Thermo J click
₹2,519.00 *
NEW
RTD click RTD click
₹1,999.00 *
NEW
Buck 11 click Buck 11 click
₹2,209.00 *
NEW
NEW
Light Temp Click Light Temp Click
₹1,789.00 *
NEW
Charger 8 click Charger 8 click
₹2,519.00 *
NEW
Buck 9 Click Buck 9 Click
₹2,209.00 *
NEW
NEW
NEW
VREG 2 click VREG 2 click
₹2,209.00 *
NEW
NEW
Nano Power click Nano Power click
₹1,159.00 *
NEW
Buck 5 click Buck 5 click
₹3,049.00 *
NEW
Boost-INV click Boost-INV click
₹2,209.00 *
NEW
NEW
Buck 3 click Buck 3 click
₹2,309.00 *
NEW
NEW
Buck 2 click Buck 2 click
₹2,729.00 *
NEW
BATT-MAN click BATT-MAN click
₹2,839.00 *
NEW
MIC33153 click MIC33153 click
₹2,209.00 *
NEW
Charger 5 click Charger 5 click
₹1,679.00 *
NEW
MIC24055 click MIC24055 click
₹3,049.00 *
NEW
Charger click Charger click
₹2,309.00 *
NEW
VREG click VREG click
₹2,519.00 *
NEW
MCP73213 click MCP73213 click
₹1,889.00 *
NEW
MCP1664 click MCP1664 click
₹2,729.00 *
NEW
BUCK click BUCK click
₹2,939.00 *
NEW
Boost click Boost click
₹2,209.00 *
NEW
NEW
Buck-Boost click Buck-Boost click
₹2,099.00 *
NEW
NEW
DC MOTOR 7 Click DC MOTOR 7 Click
₹1,999.00 *
NEW
Stepper 5 click Stepper 5 click
₹1,789.00 *
NEW
Driver click Driver click
₹1,369.00 *
Viewed