No results were found for the filter!
Jetson Nano Complete Development Kit
NVIDIA Jetson Nano Developer Kit is a small, powerful computer that lets you run multiple neural networks in parallel for applications like image classification, object detection, segmentation, and speech processing. All in an...
BladeRF 2.0 Micro Case
The case fits the bladeRF 2.0 micro. A set of screws are included for assembly. The enclosure is made of a high density yet clear PolyCarbonate material that can withstand a great amount of stress. Product includes: 1x bladeRF 2.0 micro...
This is a general purpose tri-band antenna that covers 700MHz to 2600MHz. It is a good fit as a starter antenna for research and experimentation in the ISM bands. Product includes: 1x Tri-Band Antenna Highlights: Type: Durable Rubber...
BT-200 Bias-tee Low Noise Amplifier
The BT-200 is a wideband bias-tee RX Low Noise Amplifier that draws its current from the bladeRF 2.0 micro’s SMA connectors. The BT-200 is a compact LNA solution useful for substantially lowering the noise figure and substantially...
BT-100 Bias-tee Power Amplifier
The BT-100 is a wideband bias tee TX Power Amplifier (PA) that draws its current from the bladeRF 2.0 micro’s SMA connectors. The BT-100 is versatile PA that is an ideal intermediary or final stage amplifier in a TX chain. bladeRF-cli...
FeatherWing Tripler Mini Kit - Prototyping...
This is the FeatherWing Tripler - a prototyping add-on and more for all Feather boards. This is similar to our FeatherWing Proto except there are three! The magic of the Tripler comes when you want to connect your Feather to two other...
STEMMA Wired Tactile Push-Button Pack - 5 Color...
Little clicky switches are standard input "buttons" on electronic projects. These are just like our Colorful Round Tactile Button Switch Assortment, but already assembled onto a PCB - they even have a pull-up resistor installed! The pins...
Dedicated Cooling Fan for Jetson Nano, 5V, 3PIN...
Dedicated Cooling Fan for Jetson Nano, 5V, 3PIN Reverse-proof Category: Jetson Nano cooling fan Connector: 3PIN reverse-proof connector Spec: 5V Dimensions: 40mm×40mm×10mm
AC8265 Wireless NIC for Jetson Nano, WiFi /...
This is a dual mode wireless NIC module applicable for Jetson Nano, supports 2.4GHz / 5GHz dual band WiFi and Bluetooth 4.2. Specification Chip: Intel 8265AC Bands: 2.4GHz / 5GHz Speed: 300Mbps / 867Mbps WiFi protocol: 802.11ac Bluetooth...
5V ,4A Adapter for Jetson Nano Developer Kit(B01)
5V , 4A Switching Power Supply. This is best suitable for nvidia jetson nano developer kit (B01) Plug type: 5.5mm OD / 2.1mm ID 'coaxial' DC plug Input: 110V-220V AC Output: ~5V DC up to 4A
Rain Gage - Optical Rain Sensor with relay...
Optical Rain Sensor Use it to measure rainfall or to close a skylight when it starts raining. The RG-11 Rain Gauge senses water hitting its outside surface using beams of infrared light. It uses the same sensing principle used in...
Raspberry Pi 3 Model B 1GB RAM
Did you really think the Raspberry Pi would stop getting better? At this point, we sound like a broken record, extolling on the new Pi’s myriad improvements like we’re surprised that the folks at the Raspberry Pi foundation are...
Color Pigment High Power LED Kingbright Google Coral LED SMD RGB Weighing Sensor Timer Board - Crystal 16MHz BladeRF 2.0 Uarm Swift Pro 6DoF - MPU-6050 STEMMA Wired Breadboard - IR Pair 5mm BT-100 Bias-tee FeatherWing IR optical Jumper wires f Breadboard IC Socket Adapter PCB-SMD Google AIY SMD Coin Cell Solid-State ToF BT-200 Bias-tee CO2 CARBON ESP8266 Google AIY TowerPro SG-90 Raspberry Pi 3 Heat shrink xArm 6 Google Coral 5V 4A Adapter Crystal 12Mhz IR Optical High Power LED AC8265 Wireless CNY 70 Micro SD HC 24V Solenoid Jetson Nano uArm Swift Pro Heat shrink Door Switch - 3 GPIO Header for