Close filters
 
  •  
from to
1 From 2
No results were found for the filter!
VOLT - Smart USB Li-Po battery charger
VOLT - Smart USB Li-Po battery charger
VOLT is a smart USB Li-Polymer battery charger. It features power management circuitry with MCP73832 , which can charge the battery over USB connector. Using provided screw terminals (VSYS and GND) VOLT can also be used to power your...
₹1,459.00 *
SmartPROTO Board
SmartPROTO Board
SmartPROTO board features female IDC10 connector and two prototyping areas which enable you place your own components and assemble an accessory board which can be connected with mikroElektronika development boards. First prototyping area...
₹519.00 *
Relay 4 Board
Relay 4 Board
Relay 4 Board is a cost effective solution for adding relays to your device. Single ULN2803 driver IC with 8 Darlington arrays drives each of the four available relays. Screw-terminals allow you clean and easy output relay connectivity,...
₹3,139.00 *
mikroProg to ICD2 & ICD3 adapter
mikroProg to ICD2 & ICD3 adapter
mikroProg to ICD2 & ICD3 is an adapter board which allows you to connect mikroProg™ programmer and In-Circuit debugger to target board where only ICD2/3 connector is available for programming. Board provides the necessary interface for...
₹529.00 *
Microphone AMP Board
Microphone AMP Board
The Microphone AMP Board enables you to add a power amplifier with microphone to your applications. There is an on-board Audio Power Amplifier LM4864 and microphone that can be connected to your prototype device via an on-board screw...
₹1,259.00 *
Gesture Board USB Adapter
Gesture Board USB Adapter
This I2C to USB adapter is specifically built for connecting our Gesture Board to a PC, allowing you to explore the possibilities of Microchip's MGC3130 3D gesture recognition controller. The adapter is also available already paired with...
₹1,259.00 *
Ethernet Connector Board
Ethernet Connector Board
Ethernet Connector Boards include a 10/100 Base-Transformer RJ45 connector that enables you to easily connect your prototype board to the Ethernet network. Ethernet Connector Board is a simple, yet effective solution for adding reliable...
₹1,039.00 *
CANSPI Board
CANSPI Board
CANSPI Board is a CAN development tool for microcontrollers with SPI interface. The Board includes MCP2515 CAN controller and MCP2551 transceiver. It is capable of transmitting and receiving both standard and extended data and remote...
₹2,209.00 *
Bipolar Stepper Motor Driver Board
Bipolar Stepper Motor Driver Board
The Bipolar Stepper Motor Driver Board features a complete microstepping motor driver with a built-in translator A3967SLB . It is designed to operate bipolar stepper motors in full-, half-, quarter-, and eighth-step modes, with output...
₹2,519.00 *
mikroProg to ST-Link v2 adapter
mikroProg to ST-Link v2 adapter
mikroProg to ST-Link v2 adapter allows you to connect mikroProg for STM32 programmer and hardware debugger to 20-pin male JTAG connector on your target board. Adapter is consisted of one 2x10 male header and a 2x10 female socket. It’s...
₹529.00 *
SmartGPS Board
SmartGPS Board
SmartGPS Board is a compact solution for adding GPS functionality to your device. It features popular ublox LEA-6S module, power supply circuit, USB and antenna connectors, li-polymer battery for data retention and IDC10 header for...
₹5,209.00 *
NFC USB Dongle
NFC USB Dongle
NFC USB Dongle is an NFC Reader-Writer based on NXP’s PN7150 high-performance full NFC controller, supporting all NFC Forum modes. The USB NFC Dongle is powered through USB connector. This NFC controller supports all NFC Forum...
₹3,049.00 *
1 From 2
Viewed