No results were found for the filter!
The EasyPROTO Board solves your connecting problems by offering a complete, cost-effective solution. It allows you to connect entire PORT on your development board with 2x5 male headers to a prototyping board. Easy PROTO is clearly...
R2R DAC Board
The R/2R ladder DAC is an 8-bit Digital to Analog Converter. An 8-bit value from the microcontroller port will be converted into an equivalent analog voltage by means of the R/2R resistor network. The R/2R ladder DAC makes use of only...
TFT Board 5 Capacitive with frame
TFT Board 5 Capacitive with frame is a 5" display board which features the standardized 2x20-pin display connector. The display board also integrates a capacitive multitouch panel with swipe and zoom gesture support. The TFT display...
TFT Board 7 Capacitive with frame
TFT Board 7 Capacitive with frame is a 7" display board which features the standardized 2x20-pin display connector. The display board integrates a capacitive multitouch panel with swipe and zoom gesture support. The TFT display module...
NFC Extend Click
NFC Extend Click is NFC tag interface device with possibility of using any shape and size external antenna, offering 16 Kbit of electrically erasable programmable memory (EEPROM). This Click Board™ offer two communication interfaces. The...
CAN FD Click
CAN FD Click is a add-on board based on TLE9252V CAN network transceiver, designed for HS CAN networks up to 5 Mbit/s in automotive and industrial applications. As an interface between the physical bus layer and the CAN protocol...
LPCXpresso Click Shield
LPCXpresso is the development platform pioneered by NXP® and Embedded Artists. It includes low-cost LPCXpresso target boards which are designed for simple, rapid prototyping and evaluation. LPCXpresso development boards work with the MCU...
One Shot Click
One Shot Click is equipped with the monostable multivibrator (also known as a “one-shot” pulse generator) with a programmable pulse width of 1μs to 33.6 seconds. The used LTC6993-2 is part of the TimerBlox® family of versatile silicon...
MUX 3 Click
MUX 3 Click is the general purpose multiplexer which offers multiplexing one input channel to eight single-ended output channels. Given the TMUX1208 wide operating supply options from 1.08 V to 5.5 V and support of bidirectional I/O...
RS232 SPI click
RS232 SPI click is based around the MAX3100, a universal universal asynchronous receiver transmitter (UART) - the first UART specifically optimized for small microcontroller-based systems, from Maxim Integrated. Because of the features...
Step Down 2 click
The Step Down 2 click is a Click board™ equipped with the L6986HTR, a synchronous step-down switching regulator with operating input voltages from 4V to 38V and output voltage adjustability ranges from 0.85 V to VIN. Because of the main...
Secure 7 Click
Secure 7 Click carries the ATECC608A cryptographic coprocessor with secure hardware-based key storage, from Microchip. The ATECC608A includes an EEPROM array which can be used for storage of up to 16 keys, certificates, miscellaneous...
AudioAmp 2 Thermostat 3 DAC Click RS232 SPI click FRAM 3 Click MCP2518FD click PIXI click Charger 5 click STSPIN250 click FM click 2x20W Amp click M-Bus Master LEM click RTC5 click R Meter click IrThermo click StereoAmp click BUZZ 2 click Silent Step Proximity click Temp-Log 3 Vibra sense 13DOF 2 click H-bridge 3 Moisture click DALI Click RMS to DC click GNSS 7 click GSM-GPS click DAC 3 Click Pressure click OSD click EEG click LoRa click PAC1921 click 13DOF Click Buck 13 Click Relay 3 Click Slider 2 Click Fan 2 click RTC 8 click Hz to V click V to Hz 2 click DIGI POT 4 Adapter click Knob G Click