Brushless 3 click

Please inform me as soon as the product is available again.
Please enter these characters in the following text field.
₹1,999.00 *

Prices incl. VAT plus shipping costs

Out of Stock

  • MIKROE-2766
  • MIKROE-2766
Brushless 3 click  carries the  DRV10983 , a three-phase sensorless motor driver with... more
Product information "Brushless 3 click"

Brushless 3 click carries the DRV10983, a three-phase sensorless motor driver with integrated power MOSFETs. When an external power supply is applied, you can drive a brushless DC motor through the PWM pin, AN pin or I2C interface. It communicates with the target microcontroller over I2C interface, with the additional functionality provided by the following pins on the mikroBUS™ line: PWM, AN, INT, RST.

A 3 wire BLDC motor can be connected over the screw terminals.

DRV10983 driver features

The DRV10983 is a three-phase sensorless motor driver with integrated power MOSFETs, which can provide continuous drive current up to 2A.

The DRV10983 uses a proprietary sensorless control scheme to provide continuous sinusoidal drive, which significantly reduces the pure tone acoustics that typically occurs as a result of commutation.

The interface to the device is designed to be simple and flexible. The motor can be controlled directly through PWM, analog, or I2C inputs. Motor speed feedback is available through either the FG pin or I2C.


Type DC
Applications The automotive industry, drones (because of the good power-to weight ratio of brushless motors), computers, medical equipment, HVAC systems, small home appliances, robotics, battery powered systems, small cooling fans in computers, toys, etc.
On-board modules DRV10983, a three-phase sensorless motor driver with integrated power MOSFETs.
Key Features Input voltage range from 8V to 28V
Interface GPIO,I2C
Click board size M (42.9 x 25.4 mm)

Pinout diagram

This table shows how the pinout on Brushless 3 click corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).

NotesPinMikrobus logo.pngPinNotes
  NC 1 AN PWM 16 PWM PWM output
Direction DIR 2 RST INT 15 INT FG signal output
  NC 3 CS TX 14 NC  
  NC 4 SCK RX 13 NC  
  NC 5 MISO SCL 12 SCL I2C clock
  NC 6 MOSI SDA 11 SDA I2C data
  NC 7 3.3V 5V 10 NC  
Ground GND 8 GND GND 9 GND Ground

Jumpers and settings

DesignatorNameDefault PositionDefault OptionDescription
JP1 SPEED Left PWM Speed mode selection between analog and PWM.


Code examples for Brushless 3 click, written for MikroElektronika hardware and compilers are available on Libstock.

Code snippet

The following code snippet sets the motor paremeters and measures the motor velocity.

02 sbit BRUSHLESS_3_DIR_PIN_Direction at TRISC.B0;
04 sbit BRUSHLESS_3_PWM_PIN_Direction at TRISC.B1;
05 uint8_t motorParameters [12] = { 0x39, 0x1E, 0x3A, 0x08, 0x50, 0xDA, 0x8B, 0x10, 0x27, 0x37, 0x04, 0x0C} ;
06 uint16_t Velocity;
07 char text[10];
08 void systemInit()
09 {
10     ANCON0 = 0x00;
11     ANCON1 = 0x00;
12     ANCON2 = 0x00;
13     BRUSHLESS_3_DIR_PIN_Direction = 0;
14     BRUSHLESS_3_PWM_PIN_Direction = 0;
15     I2C1_Init (100000);
16     Delay_ms(100);
17     BRUSHLESS_3_I2CdriverInit( I2C1_Start, I2C1_Stop, I2C1_Repeated_Start, I2C1_Wr, I2C1_Rd);
18     UART1_Init(9600);
19     Delay_ms(100);
20     UART1_Write_Text("Init");
21 }
22 void Brushless_3_Init()
23 {
24     BRUSHLESS_3_DIR_PIN = 0;
25     BRUSHLESS_3_PWM_PIN = 1;
26     writeParameters(motorParameters);
27 }
28 void Brushless_3_Task()
29 {
30     getSpeed(&Velocity);
31     IntToStr(Velocity,text);
32     UART1_Write_Text( "Motor freq :" );
33     UART1_Write_Text(text);
34     UART1_Write_Text( "Hzrn" );
35     delay_ms(1000);
36 }
37 void main()
38 {
39     systemInit();
40     Brushless_3_Init();
41     while( 1 )
42     {
43             Brushless_3_Task();
44     }
45 }


Related links to "Brushless 3 click"
Read, write and discuss reviews... more
Customer evaluation for "Brushless 3 click"
Write an evaluation
Evaluations will be activated after verification.
Please enter these characters in the following text field.

The fields marked with * are required.