Top seller
No results were found for the filter!
RS485 3 click uses SN65HVD31DR from Texas Instruments , a tri-state differential line driver and differential input line receiver. The click is intended to be used as UART to RS422/RS485 communication interface. It is suited for...
₹2,099.00 *
USB UART 4 click features well-known FT232RL USB-to-UART interface module from FDTI . It provides USB to asynchronous serial data transfer interface, allowing the microcontroller based designs to communicate with the personal computer,...
₹1,459.00 *
MCP2517FD click is a complete CAN solution which carries the MCP2517FD CAN FD controller and ATA6563 high-speed CAN transceiver from Microchip, as well as a DB9 9-pin connector. The click requires both 3.3V and 5V power supply. It...
₹2,629.00 *
1-Wire I2C click carries DS28E17 1-Wire-to-I2C master bridge from Maxim Integrated. The click runs on a 3.3V power supply. It communicates with the target microcontroller over 1-Wire® protocol, using the following pins on the mikroBUS™...
₹2,309.00 *
RS485 Isolator click is a RS485 communication isolator, and carries the ADM2682EBRIZ , a 5 kV rms signal and power isolated RS-485 transceiver. The click is designed to run on either 3.3V or 5V power supply. It communicates with the...
₹5,149.00 *
CAN Isolator click provides isolated CAN communication. It carries the ADM3053 signal and power isolated CAN transceiver with an integrated isolated DC-to-DC converter. The click is designed to run on either 3.3V or 5V power supply. CAN...
₹4,099.00 *
ATA6563 click carries the ATA6563 high-speed CAN transceiver. The click is designed to run on a 5V power supply. Use the VIO SEL jumper for selecting the 3.3V or 5V logic level. It communicates with the target microcontroller over UART...
₹2,099.00 *
RS485 2 click carries the MAX3471 half-duplex transceiver intended for lithium battery-powered RS-485/RS-422 applications. The click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller...
₹1,889.00 *
I2C Isolator 2 click provides I2C lines and power isolation for slave devices. It carries the ADM3260 dual I2C isolator with an integrated DC-to-DC converter. I2C Isolator 2 click is designed to run on either 3.3V or 5V power supply. The...
₹2,519.00 *
USB UART 2 click provides USB isolation and carries the ADUM4160BRWZ USB port isolator. The click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller over UART interface, with additional...
₹4,099.00 *
SPI Isolator click carries the ADuM4154 5kV digital isolator optimized for a serial peripheral interface (SPI). The click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller over SPI...
₹3,049.00 *
The click communicates with the target MCU through the UART interface and runs on a 3.3V power supply. ATA663211 click can aslo be used as a standalone LIN transceiver, without being connected to a mikroBUS™ socket. An onboard LDO...
₹1,999.00 *
ATA663254 click ETH WIZ click CAN Isolator I2C 1-Wire Fiber Opt click PWM click OBDII click RS485 3 click LIN Click CAN SPI click USB I2C click Dual LIN click DALI Click USB SPI click ATA6563 click USB UART 2 MCP2517FD click BroadR-Reach RS232 SPI click MCP2518FD click RS485 4 Click UART I2C SPI LLC SPI Click PS 2 click iButton click MCP25625 click ETH Click FTDI click I2C to SPi USB UART 3 RS485 2 click PWM 2 click USB UART 4 SPI Isolator MCP2003B click EXPAND click Expand 2 click ATA6570 click UART 1-Wire M-Bus Master Terminal click RS232 2 click RS232 Isolator I2C Isolator 2 RS485 click 4-20 mA T click
Viewed