No results were found for the filter!
LPCXpresso Click Shield
LPCXpresso is the development platform pioneered by NXP® and Embedded Artists. It includes low-cost LPCXpresso target boards which are designed for simple, rapid prototyping and evaluation. LPCXpresso development boards work with the MCU...
Feather Click Shield
The Feather is Adafruit’s standardized open source development platform for IoT projects. The Adafruit Feather & FeatherWing system consist of base board (Feather) and expansion boards (Wings). They are connected to each other over...
mikroBUS Shuttle is a small add-on board, which is intended to be used with Shuttle click , in order to expand the mikroBUS™ with additional stacking options. This small add-on board has one mikroBUS™ equipped on itself and it is...
USB I2C click
USB I2C click carries an MCP2221 USB-to-UART/I2C converter. The chip supports full-speed USB (12 Mb/s), I2C with up to 400 kHz clock rates and UART baud rates between 300 and 115200. The board communicates with the target MCU through...
MCP2542 is designed specifically for high-speed CAN FD applications with communication speeds of up to 8 Mbps. Longer than usual BUS lengths are supported thanks to the improved maximum propagation delay. The board has a standard RS232...
RS485 Isolator click
RS485 Isolator click is a RS485 communication isolator, and carries the ADM2682EBRIZ , a 5 kV rms signal and power isolated RS-485 transceiver. The click is designed to run on either 3.3V or 5V power supply. It communicates with the...
CAN Isolator click
CAN Isolator click provides isolated CAN communication. It carries the ADM3053 signal and power isolated CAN transceiver with an integrated isolated DC-to-DC converter. The click is designed to run on either 3.3V or 5V power supply. CAN...
ATA6563 click carries the ATA6563 high-speed CAN transceiver. The click is designed to run on a 5V power supply. Use the VIO SEL jumper for selecting the 3.3V or 5V logic level. It communicates with the target microcontroller over UART...
RS485 2 click
RS485 2 click carries the MAX3471 half-duplex transceiver intended for lithium battery-powered RS-485/RS-422 applications. The click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller...
I2C Isolator 2 click
I2C Isolator 2 click provides I2C lines and power isolation for slave devices. It carries the ADM3260 dual I2C isolator with an integrated DC-to-DC converter. I2C Isolator 2 click is designed to run on either 3.3V or 5V power supply. The...
USB UART 2 Click
USB UART 2 click provides USB isolation and carries the ADUM4160BRWZ USB port isolator. The click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller over UART interface, with additional...
SPI Isolator click
SPI Isolator click carries the ADuM4154 5kV digital isolator optimized for a serial peripheral interface (SPI). The click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller over SPI...
Arduino MEGA RS232 2 click RS485 click 5V PWM 2 click I2C Isolator ATA6563 click UART 1-Wire RS485 3 click Intel Joule LLC-I2C Click USB UART click USB SPI click Pi click shield ETH Click FTDI click iButton click Expand 4 click RS485 4 Click RS485 2 click PI2 click MCP2517FD click STM32F4 I2C 1-Wire ATA663254 click USB UART 3 I2C Isolator 2 PS 2 click FRDM KL46 click SPI Isolator UART I2C SPI MCP25625 click Intel Joule MCP2003B click DALI Click BroadR-Reach RS232 click Arduino UNO EXPAND click ATA663211 click PICtail Plus 4-20 mA R click mikroBus Cape Expand 3 click MCP2518FD click 1-Wire I2C RS485 Isolator