No results were found for the filter!
Brushless 3 click
Brushless 3 click carries the DRV10983 , a three-phase sensorless motor driver with integrated power MOSFETs. When an external power supply is applied, you can drive a brushless DC motor through the PWM pin, AN pin or I2C interface. It...
Brushless 2 click
Brushless 2 click carries the DRV10964 BLDC motor controller with an integrated output stage from Texas Instruments. The click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller over the...
Stepper 4 click
Stepper 4 click carries the TB67S269FTG , a two-phase bipolar stepping motor driver from Toshiba. The click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller over the following pins on...
Fan 2 click
Fan 2 click carries the MAX31760 precision fan-speed controller. It can measure temperature and adjust the fan speed to keep the temperature at the same level. Fan 2 click can also control two fans at the same time. The click is designed...
DC MOTOR 5 click
DC MOTOR 5 click carries the DRV8701 brushed DC motor gate driver from Texas Instruments. The click is designed to run on an external power supply. It communicates with the target MCU over the following pins on the mikroBUS™ line: AN,...
DC MOTOR 4 click
DC MOTOR 4 click is capable of driving motors with a supply voltage from 4.5V to 36V . It carries the MAX14870 motor driver from Maxim Integrated. The click is designed to run on either 3.3V or 5V power supply. DC MOTOR 4 click...
PWM driver click
If you need to control DC motors with loads up to 10A, PWM driver click is the perfect solution, thanks to the Silicon Lab Si8711CC one-channel isolator. It communicates with the target MCU over PWM pin, and runs on a 5V power supply. It...
DC MOTOR 3 Click
Two pairs of screw terminals are positioned on the top of the board. One is for bringing an external power supply; the other is for connecting a motor. TB6549FG has four operating modes: clockwise, counter-clockwise, short brake and...
Stepper 3 click
The board carries a Texas Instruments ULN2003 High-Current Darlington transistor array for operating the motors. Motors are connected through a 4-pin male connector on the top of the PCB. They can be driven by the click board's own power...
Stepper 2 click
Stepper 2 click is a complete solution for driving bipolar stepper motors with full/half and micro-steps. It features the A4988 IC from Allegro Microsystems with DMOS low RDSON drivers on its outputs, which ensure high efficiency and...
Haptic click carries DRV2605 , a Haptic Driver for ERM and LRA vibration motors (acronyms stand for Eccentric Rotating Mass and Linear Resonant Actuator, respectively). The DRV2605 IC integrates an extensive library with over 100 haptic...
Fan click carries an EMC2301 controller for powering and regulating the operation of 5V four-wire fans, which are commonly utilized as coolers in computers and other electronics. The controller supports PWM speeds from 9.5Hz to 29 KHz,...
Fan click H-Bridge 2 DC Motor 11 DC MOTOR 5 Fan 4 click STSPIN820 click DC Motor 9 STSPIN250 click Stepper 13 Stepper 7 click Fan 2 click Brushless 4 H-Bridge click PWM driver DC MOTOR 3 Stepper 5 click Servo click DC MOTOR 4 Brushless 5 STSPIN220 click H-bridge 3 Stepper 3 click Silent Step DC MOTOR 2 Stepper 2 click Brushless 3 DC Motor 8 Fan 3 click STSPIN233 click Vibro Motor Fan 6 click Brushless 6 Brushless 2 Stepper click H-Bridge 5 DC Motor 10 DC MOTOR click HAPTIC click Stepper 4 click Driver click Silent Step 3 DC MOTOR 7 H-Bridge 4