LSM6DSL click

Please inform me as soon as the product is available again.
Please enter these characters in the following text field.
₹1,579.00 *

Prices incl. VAT plus shipping costs

Out of Stock

  • MIKROE-2731
  • MIKROE-2731
LSM6DSL click  measures linear and angular velocity with six degrees of freedom. It... more
Product information "LSM6DSL click"

LSM6DSL click measures linear and angular velocity with six degrees of freedom. It carries the LSM6DSL high-performance 3-axis digital accelerometer and 3-axis digital gyroscope. The click is designed to run on a 3.3V power supply. LSM6DSL click communicates with the target microcontroller over SPI or I2C interface, with additional functionality provided by the INT pin on the mikroBUS™ line.

Mode 1: I2C slave interface or SPI serial interface is available.

Mode 2: I2C slave interface, or SPI serial interface and I2C interface master for external sensor connections, are available.

LSM6DSL inertial module features

The LSM6DSL is a system-in-package featuring a 3D digital accelerometer and a 3D digital gyroscope performing at 0.65 mA in high-performance mode and enabling always-on low-power features for an optimal motion experience.

The event-detection interrupts enable efficient and reliable motion tracking and contextual awareness, implementing hardware recognition of free-fall events, 6D orientation, click and double-click sensing, activity or inactivity, and wakeup events

The LSM6DSL has a full-scale acceleration range of ±2/±4/±8/±16 g and an angular rate range of ±125/±245/±500/±1000/±2000 dps (degrees per second).

Specifications

Type Motion
Applications Motion tracking and gesture detection, indoor navigation, vibration monitoring and compensation, etc.
On-board modules LSM6DSL
Key Features Power consumption: 0.4 mA in combo normal and 0.65 mA in combo high-performance mode; hard, soft ironing for external magnetic sensor corrections
Interface I2C,SPI
Input Voltage 3.3V
Click board size M (42.9 x 25.4 mm)

Pinout diagram

This table shows how the pinout on LSM6DSL click corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).

NotesPinMikrobus logo.pngPinNotes
  NC 1 AN PWM 16 NC  
  NC 2 RST INT 15 INT Programmable interrupt 
Chip select CS 3 CS TX 14 NC  
SPI clock SCK 4 SCK RX 13 NC  
Master input slave output MISO 5 MISO SCL 12 SCL I2C clock
Master output slave input MOSI 6 MOSI SDA 11 SDA I2C data
Power supply +3.3V 7 3.3V 5V 10 NC  
Ground GND 8 GND GND 9 GND Ground

Jumpers and settings

DesignatorNameDefault PositionDefault OptionDescription
JP1 COMM SEL Left SPI Communication Interface Selection SPI/I2C, left position SPI, right position I2C
JP2 COMM SEL Left SPI Communication Interface Selection SPI/I2C, left position SPI, right position I2C
JP3 COMM SEL Left SPI Communication Interface Selection SPI/I2C, left position SPI, right position I2C
JP4 INT SEL Left INT1 Interrupt selection INT1/INT2, left position INT1, right position INT2
JP5 COMM SEL Left SPI Communication Interface Selection SPI/I2C, left position SPI, right position I2C
JP6 MODE SEL Left 1 Mode Selection 1/2, left position 1, right position 2
JP7 MODE SEL Left 1 Mode Selection 1/2, left position 1, right position 2
JP8 ADD SEL Left 0 I2C slave address selection 0/1, left position 0, right position 1

Programming

Code examples for LSM6DSL click, written for MikroElektronika hardware and compilers are available on Libstock.

Code snippet

The following code snippet initializes the module, the driver, and peripherals, and then outputs the measured data to UART every two seconds.

01 void main()
02 {
03     char txt [100];
04     float x,y,z;
05
06     systemInit();
07     LSM6DSL_initDriver(SPI3_Write, SPI3_Read);
08     UART1_Write_Text ("rnInitialized");
09
10     /*
11      * Starts measurements for acceleration and rotation at specified
12      * rate (104 HZ) and selected full-scale (+-2G, +-245DPS).
13      */
14     LSM6DSL_configureRead (CONFIG_ACCELERATION, ODR_104_HZ | FULLSCALE_A_2);
15     LSM6DSL_configureRead (CONFIG_ROTATION, ODR_104_HZ | FULLSCALE_R_245);
16     while( 1 )
17     {
18          UART1_Write_Text ("rnrnAcceleration values in mili-Gs:");
19          LSM6DSL_readAccelerationXYZ (&x, &y, &z, FULLSCALE_A_2);
20          sprintf (txt, "rnX: %.2f, t Y:%.2f, t Z: %.2f", x,y,z);
21          Uart1_Write_Text (txt);
22
23          UART1_Write_Text ("rnRotation values in degrees per second:");
24          LSM6DSL_readRotationXYZ (&x, &y, &z, FULLSCALE_R_245);
25          //Values are read in mili-degrees per second, so they need to be divided by 1000
26          sprintf (txt,
27           "rnPitch: %.2f, t Roll:%.2f, t Yaw: %.2f", x/1000,y/1000,z/1000);
28          Uart1_Write_Text (txt);
29
30          delay_ms (2000);
31     }
32 }

 

Related links to "LSM6DSL click"
Read, write and discuss reviews... more
Customer evaluation for "LSM6DSL click"
Write an evaluation
Evaluations will be activated after verification.
Please enter these characters in the following text field.

The fields marked with * are required.

Viewed