MCP2517FD click

Please inform me as soon as the product is available again.
Please enter these characters in the following text field.
₹2,629.00 *

Prices incl. VAT plus shipping costs

Out of Stock

  • MIKROE-2379
  • MIKROE-2379
MCP2517FD click  is a complete CAN solution which carries the  MCP2517FD  CAN... more
Product information "MCP2517FD click"

MCP2517FD click is a complete CAN solution which carries the MCP2517FD CAN FD controller and ATA6563 high-speed CAN transceiver from Microchip, as well as a DB9 9-pin connector.

The click requires both 3.3V and 5V power supply. It communicates with the target microcontroller through the SPI interface, with additional functionality provided by the following pins on the mikroBUS™ socket: AN, PWM, INT, TX and RX.

Note: For selecting the interface voltage level, use the onboard jumper, and choose between the 3.3V and 5V. For more information, see the Jumpers and Settings table below.

MCP2517FD features

The MCP2517FD is a cost-effective and small-footprint CAN FD controller that can be easily connected to a microcontroller over an SPI interface. Therefore, a CAN FD channel can be easily added to a microcontroller that is either lacking a CAN FD peripheral, or that doesn’t have enough CAN FD channels.

The MCP2517FD supports both, CAN frames in the Classical format (CAN2.0B) and CAN Flexible Data Rate (CAN FD) format.

ATA6563 CAN transceiver features

ATA6563 is a high-speed CAN transceiver that provides an interface between a controller area network (CAN) protocol controller and the physical two-wire CAN bus.

The transceiver is designed for high-speed (up to 5Mbit/s) CAN applications in the automotive industry, providing differential transmit and receive capability.

It offers improved electromagnetic compatibility (EMC) and electrostatic discharge (ESD) performance.

Connector features

This is a standard DB 9-pin male connector.


Type CAN
Applications Simple solution for adding CAN FD connectivity to your device
On-board modules 9-pin CAN connector, ATA6563 CAN transceiver
Key Features Communication speed up to 5Mbit/s, low electromagnetic emission (EME) and high electromagnetic immunity (EMI)
Interface SPI
Input Voltage 3.3V or 5V
Compatibility mikroBUS
Click board size L (57.15 x 25.4 mm)

Pinout diagram

This table shows how the pinout on MCP2517FD click corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).

Notes Pin Mikrobus logo.png Pin Notes
Standby mode control input STBY 1 AN PWM 16 CLKO Clock output
  NC 2 RST INT 15 nINT Interrupt output
Chip select nCS 3 CS TX 14 nINT0 Interrupt output/transceiver standby/GPIO
SPI Clock SCK 4 SCK RX 13 nINT1 Interrupt output/GPIO
SPI Master Input Slave Output MISO 5 MISO SCL 12 NC  
SPI Master Output Slave Input MOSI 6 MOSI SDA 11 NC  
Power supply +3.3V 7 3.3V 5V 10 +5V Power supply
Ground GND 8 GND GND 9 GND Ground

Additional pins

Name I/O Description
TX_CAN   CAN transmit
RX_CAN   CAN receive
CANL   CAN low line
CANH   CAN high line

Jumpers and settings

Designator Name Default Position Default Option Description
JP1 VIO.SEL. Left 3V3 Power Supply Voltage Selection 3V3/5V, left position 3V3, right position 5V
JP2 STBY Right ON Select Stand by function, default ON, other takes the STBY SEL configuration
JP3 STBY SEL Left STBY Takes STBY input from STBY pin or INT0 pin on mikroBUS™
JP4   Right 40MHz Selects between 20 and 40 MHz clock

LEDs and buttons

Designator Name Type Description
CN1   CONNECTOR DB9 connector for CAN


Code examples for MCP2517FD click, written for MikroElektronika hardware and compilers are available on Libstock.

Code snippet

The following code snippet shows the transmission using MCP2517FD CAN FD controller.

01 void transmitMessage( char *msg )
02 {
03     T_MCP2517FD_txFifoEvent     txFlags;
04     T_MCP2517FD_txMsgObj        txObj;
05     uint8_t                     txData[_MCP2517FD_MAX_DATA_BYTES];
06     bool                        flush;
08     flush = true;
09     txObj.word[0] = 0;
10     txObj.word[1] = 0;
12 = 0x300;
13 = 0;
14     txObj.bF.ctrl.FDF = 1;
15     txObj.bF.ctrl.BRS = 1;
16     txObj.bF.ctrl.IDE = 0;
17     txObj.bF.ctrl.RTR = 0;
18     txObj.bF.ctrl.DLC = MCP2517FD_DLC_64;
19     txObj.bF.ctrl.SEQ = 1;
21     memset(txData, 0, _MCP2517FD_MAX_DATA_BYTES);
22     strcpy(txData, msg);
23     MCP2517FD_TransmitEventGet(MCP2517FD_IDX, &txFlags);
25     if( txFlags & MCP2517FD_TX_FIFO_NOT_FULL )
26     {
27         MCP2517FD_TransmitChannelLoad(MCP2517FD_IDX, MCP2517FD_FIFO_CH1, &txObj,
28                 txData, MCP2517FD_DlcToDataBytes(txObj.bF.ctrl.DLC), flush);
29         LOG( "rn MCP2517FD : Message sent! > " );
30         LOG( txData );
31         LOG( "rn" );
32     }
33     else
34     {
35         LOG( "rn MCP2517FD : Message not sent! >rn" );
36     }
37 }


 mikroBUS™ Standard specification 
 MCP2517FD click schematic
 ATA6563 datasheet
 MCP2517FD datasheet

 LibStock: MCP2517FD click examples 

Related links to "MCP2517FD click"
Read, write and discuss reviews... more
Customer evaluation for "MCP2517FD click"
Write an evaluation
Evaluations will be activated after verification.
Please enter these characters in the following text field.

The fields marked with * are required.